Driver: 8255.o
Description: generic 8255 support
Devices: [standard] 8255 (8255)
Author: ds
Status: works
Updated: Fri,  7 Jun 2002 12:56:45 -0700

The classic in digital I/O.  The 8255 appears in Comedi as a single
digital I/O subdevice with 24 channels.  The channel 0 corresponds
to the 8255's port A, bit 0; channel 23 corresponds to port C, bit
7.  Direction configuration is done in blocks, with channels 0-7,
8-15, 16-19, and 20-23 making up the 4 blocks.  The only 8255 mode
supported is mode 0.

You should enable compilation this driver if you plan to use a board
that has an 8255 chip.  For multifunction boards, the main driver will
configure the 8255 subdevice automatically.

This driver also works independently with ISA and PCI cards that
directly map the 8255 registers to I/O ports, including cards with
multiple 8255 chips.  To configure the driver for such a card, the
option list should be a list of the I/O port bases for each of the
8255 chips.  For example,

  comedi_config /dev/comedi0 8255 0x200,0x204,0x208,0x20c

Note that most PCI 8255 boards do NOT work with this driver, and
need a separate driver as a wrapper.  For those that do work, the
I/O port base address can be found in the output of 'lspci -v'.




Driver: adl_pci9111.o
Description: Driver for the Adlink PCI-9111HR card.
Author: Emmanuel Pacaud <emmanuel.pacaud@free.fr>
Devices: [ADLink] PCI-9111HR (adl_pci9111)
Status: experimental

Supports:

  - ai_insn read
  - ao_insn read/write
  - di_insn read
  - do_insn read/write
  - ai_do_cmd mode with the following sources:
  
    - start_src 		TRIG_NOW
    - scan_begin_src 		TRIG_FOLLOW 	TRIG_TIMER	TRIG_EXT
    - convert_src				TRIG_TIMER	TRIG_EXT
    - scan_end_src		TRIG_COUNT
    - stop_src			TRIG_COUNT	TRIG_NONE
    
    The scanned channels must be consecutive and start from 0. They must
    all have the same range and aref.
    
Configuration options:
  
    [0] - PCI bus number (optional)
    [1] - PCI slot number (optional)
    
    If bus/slot is not specified, the first available PCI
    device will be used.
  



Driver: adl_pci9118.o
Description: Adlink PCI-9118DG, PCI-9118HG, PCI-9118HR
Author: Michal Dobes <majkl@tesnet.cz>
Devices: [ADLink] PCI-9118DG (pci9118dg), PCI-9118HG (pci9118hg),
  PCI-9118HR (pci9118hr)
Status: works

This driver supports AI, AO, DI and DO subdevices.
AI subdevice supports cmd and insn interface,
other subdevices support only insn interface.
For AI:
- If cmd->scan_begin_src=TRIG_EXT then trigger input is TGIN (pin 46).
- If cmd->convert_src=TRIG_EXT then trigger input is EXTTRG (pin 44).
- If cmd->start_src/stop_src=TRIG_EXT then trigger input is TGIN (pin 46).
- It is not neccessary to have cmd.scan_end_arg=cmd.chanlist_len but
  cmd.scan_end_arg modulo cmd.chanlist_len must by 0.
- If return value of cmdtest is 5 then you've bad channel list
  (it isn't possible mixture S.E. and DIFF inputs or bipolar and unipolar
  ranges).

There are some hardware limitations:
a) You cann't use mixture of unipolar/bipoar ranges or differencial/single 
   ended inputs.
b) DMA transfers must have the length aligned to two samples (32 bit),
   so there is some problems if cmd->chanlist_len is odd. This driver tries
   bypass this with adding one sample to the end of the every scan and discard
   it on output but this cann't be used if cmd->scan_begin_src=TRIG_FOLLOW
   and is used flag TRIG_WAKE_EOS, then driver switch to interrupt driven mode 
   with interrupt after every sample.
c) If isn't used DMA then you can use only mode where 
   cmd->scan_begin_src=TRIG_FOLLOW.

Configuration options:
  [0] - PCI bus of device (optional)
  [1] - PCI slot of device (optional)
          If bus/slot is not specified, then first available PCI
          card will be used.
  [2] - 0= standard 8 DIFF/16 SE channels configuration
        n= external multiplexer connected, 1<=n<=256
  [3] - 0=autoselect DMA or EOC interrupts operation
        1=disable DMA mode
        3=disable DMA and INT, only insn interface will work
  [4] - sample&hold signal - card can generate signal for external S&H board
        0=use SSHO (pin 45) signal is generated in onboard hardware S&H logic
        0!=use ADCHN7 (pin 23) signal is generated from driver, number 
           say how long delay is requested in ns and sign polarity of the hold
           (in this case external multiplexor can serve only 128 channels)
  [5] - 0=stop measure on all hardware errors
        2|=ignore ADOR - A/D Overrun status
	8|=ignore Bover - A/D Burst Mode Overrun status
	256|=ignore nFull - A/D FIFO Full status




Driver: adv_pci1710.o
Description: Advantech PCI-1710, PCI-1710HG, PCI-1711, PCI-1713,
             Advantech PCI-1720, PCI-1731
Author: Michal Dobes <majkl@tesnet.cz>
Devices: [Advantech] PCI-1710 (pci1710), PCI-1710HG (pci1710hg),
  PCI-1711 (pci1711), PCI-1713 (pci1713), PCI-1720 (pci1720),
  PCI-1731 (pci1731)
Status: works

This driver supports AI, AO, DI and DO subdevices.
AI subdevice supports cmd and insn interface,
other subdevices support only insn interface.

The PCI-1710 and PCI-1710HG have the same PCI device ID, so the
driver cannot distinguish between them, as would be normal for a
PCI driver.

Configuration options:
  [0] - PCI bus of device (optional)
  [1] - PCI slot of device (optional)
          If bus/slot is not specified, the first available PCI
          device will be used.



Driver: amplc_pc236.o
Description: Driver for Amplicon PC36AT and PCI236 DIO boards
Author: Ian Abbott <abbotti@mev.co.uk>
Devices: [Amplicon] PC36AT (pc36at), PCI236 (pci236)
Updated: Fri, 23 Aug 2002 11:41:11 +0100
Status: works

Configuration options - PC36AT:
  [0] - I/O port base address
  [1] - IRQ (optional)

Configuration options - PCI236:
  [0] - PCI bus of device (optional)
  [1] - PCI slot of device (optional)
  If bus/slot is not specified, the first available PCI device will be
  used.

The PC36AT ISA board and PCI236 PCI board have a single 8255 appearing
as subdevice 0.

Subdevice 1 pretends to be a digital input device, but it always returns
0 when read. However, if you run a command with scan_begin_src=TRIG_EXT,
a rising edge on port C bit 7 acts as an external trigger, which can be
used to wake up tasks.  This is like the comedi_parport device, but the
only way to physically disable the interrupt on the PC36AT is to remove
the IRQ jumper.  If no interrupt is connected, then subdevice 1 is
unused.



Driver: amplc_pc263.o
Description: Driver for Amplicon PC263 and PCI263 Relay boards
Author: Ian Abbott <abbotti@mev.co.uk>
Devices: [Amplicon] PC263 (pc263), PCI263 (pci263)
Updated: Tue, 20 Aug 2002 11:41:01 +0100
Status: works

Configuration options - PC263:
  [0] - I/O port base address

Configuration options - PCI263:
  [0] - PCI bus of device (optional)
  [1] - PCI slot of device (optional)
  If bus/slot is not specified, the first available PCI device will be
  used.

Each board appears as one subdevice, with 16 digital outputs, each
connected to a reed-relay. Relay contacts are closed when output is 1.
The state of the outputs can be read.



Driver: amplc_pci230.o
Description: Driver for Amplicom PCI230 and PCI260 Multifunction I/O boards
Author: Allan Willcox <allanwillcox@ozemail.com.au>
Updated: Mon,  3 Sep 2001 17:37:12 -0700
Devices: [Amplicon] PCI230 (amplc_pci230), PCI260
Status: unknown




Driver: cb_pcidas.o
Description: Driver for the ComputerBoards/MeasurementComputing cards
  of the PCI-DAS series with the AMCC S5933 PCI controller.
Author: Ivan Martinez <ivanmr@altavista.com>,
  Frank Mori Hess <fmhess@uiuc.edu>
Updated: 2002-1-09
Devices: [Measurement Computing] PCI-DAS1602/16 (cb_pcidas),
  PCI-DAS1602/16jr, PCI-DAS1602/12, PCI-DAS1200, PCI-DAS1200jr,
  PCI-DAS1000, PCI-DAS1001, PCI_DAS1002

Status:
  - PCI-DAS1602/16: Analog input is tested, works.  Analog output untested.
  - PCI-DAS1602/16jr: Driver should work, but untested.  Please
      report usage.
  - PCI-DAS1602/12: Same as above.
  - PCI-DAS1200, 1200jr: Tested, works.
  - PCI-DAS1000, 1001, 1002: Should work, but untested.  Please report
    usage.

  The boards' autocalibration features are not yet supported.

Configuration options:
  [0] - PCI bus of device (optional)
  [1] - PCI slot of device (optional)
  If bus/slot is not specified, the first available PCI
  device will be used.

For commands, the scanned channels must be consecutive
(i.e. 4-5-6-7, 2-3-4,...), and must all have the same
range and aref.



Driver: cb_pcidas64.o
Description: Driver for the ComputerBoards/MeasurementComputing
   PCI-DAS64xx, 60XX, and 4020 series with the PLX 9080 PCI controller.
Author: Frank Mori Hess <fmhess@users.sourceforge.net>
Status: works, but no streaming analog output yet
Updated: 2002-07-18
Devices: [Measurement Computing] PCI-DAS6402/16 (cb_pcidas64),
  PCI-DAS6402/12, PCI-DAS64/M1/16, PCI-DAS64/M2/16,
  PCI-DAS64/M3/16, PCI-DAS6402/16/JR, PCI-DAS64/M1/16/JR,
  PCI-DAS64/M2/16/JR, PCI-DAS64/M3/16/JR, PCI-DAS64/M1/14,
  PCI-DAS64/M2/14, PCI-DAS64/M3/14, PCI-DAS6023E, PCI-DAS6025E, PCI-DAS6034E,
  PCI-DAS6035E, PCI-DAS4020/12

Configuration options:
   [0] - PCI bus of device (optional)
   [1] - PCI slot of device (optional)

Feel free to send and success/failure reports to Frank Hess.

Some devices are not identified because the PCI device IDs are not yet
known. If you have such a board, contact Frank Hess and the ID can be
easily added.




Driver: cb_pcidda.o
Description: ComputerBoards/MeasurementComputing PCI-DDA series
Author: Ivan Martinez <ivanmr@altavista.com>, Frank Mori Hess <fmhess@users.sourceforge.net>
Status: Supports 08/16, 04/16, 02/16, 08/12, 04/12, and 02/12
Devices: [Measurement Computing] PCI-DDA08/12 (cb_pcidda), PCI-DDA04/12,
  PCI-DDA02/12, PCI-DDA08/16, PCI-DDA04/16, PCI-DDA02/16

Configuration options:
  [0] - PCI bus of device (optional)
  [1] - PCI slot of device (optional)
  If bus/slot is not specified, the first available PCI
  device will be used.

Only simple analog output writing is supported.

So far it has only been tested with:
  - PCI-DDA08/12
Please report sucess/failure with other different cards to
<comedi@comedi.org>.



Driver: cb_pcimdda.o
Description: A driver for this relatively new and uniquely designed board
Devices: [Computer Boards] PCIM-DDA06-16 (pcimdda06-16)
Author: Calin Culianu <calin@ajvar.org>
Updated: Thu, 20 Jun 2002 16:19:41 -0500
Status: works

All features of the PCIM-DDA06-16 board are supported.  This board
has 6 16-bit AO channels, and the usual 8255 DIO setup.  (24 channels, 
configurable in banks of 8 and 4, etc.).  This board does not support commands.

The board has a peculiar way of specifying AO gain/range settings -- You have
1 jumper bank on the card, which either makes all 6 AO channels either
5 Volt unipolar, 5V bipolar, 10 Volt unipolar or 10V bipolar. 
  
Since there is absolutely _no_ way to tell in software how this jumper is set
(well, at least according  to the rather thin spec. from Measurement Computing
 that comes with the board), the driver assumes the jumper is at its factory 
default setting of +/-5V.

Also of note is the fact that this board features another jumper, whose
state is also completely invisible to software.  It toggles two possible AO
output modes on the board:

  - Update Mode: Writing to an AO channel instantaneously updates the actual
    signal output by the DAC on the board (this is the factory default).
  - Simultaneous XFER Mode: Writing to an AO channel has no effect until
    you read from any one of the AO channels.  This is useful for loading
    all 6 AO values, and then reading from any one of the AO channels on the 
    device to instantly update all 6 AO values in unison.  Useful for some
    control apps, I would assume?  If your jumper is in this setting, then you 
    need to issue your comedi_data_write()s to load all the values you want,
    then issue one comedi_data_read() on any channel on the AO subdevice
    to initiate the simultaneous XFER.
 

Configuration Options:
  Just tell comedi_config that you want to use the cb_pcimdda driver as so:

  comedi_config /dev/comedi0 cb_pcimdda



Driver: comedi_parport.o
Description: Standard PC parallel port
Author: ds
Status: works in immediate mode
Devices: [standard] parallel port (comedi_parport)
Updated: Tue, 30 Apr 2002 21:11:45 -0700

A cheap and easy way to get a few more digital I/O lines.  Steal
additional parallel ports from old computers or your neighbors'
computers.

Option list:
 0: I/O port base for the parallel port.
 1: IRQ

Parallel Port Lines:

pin     subdev  chan    aka
---     ------  ----    ---
1       2       0       strobe
2       0       0       data 0
3       0       1       data 1
4       0       2       data 2
5       0       3       data 3
6       0       4       data 4
7       0       5       data 5
8       0       6       data 6
9       0       7       data 7
10      1       3       acknowledge
11      1       4       busy
12      1       2       output
13      1       1       printer selected
14      2       1       auto LF
15      1       0       error
16      2       2       init
17      2       3       select printer
18-25   ground

Notes:

Subdevices 0 is digital I/O, subdevice 1 is digital input, and
subdevice 2 is digital output.  Unlike other Comedi devices,
subdevice 0 defaults to output.

Pins 13 and 14 are inverted once by Comedi and once by the
hardware, thus cancelling the effect.

Pin 1 is a strobe, thus acts like one.  There's no way in software
to change this, at least on a standard parallel port.

Subdevice 3 pretends to be a digital input subdevice, but it always
returns 0 when read.  However, if you run a command with
scan_begin_src=TRIG_EXT, it uses pin 10 as a external triggering
pin, which can be used to wake up tasks.



Driver: comedi_rt_timer.o
Description: Command emulator using real-time tasks
Author: ds, fmhess
Devices:
Status: works

This driver requires RTAI or RTLinux to work correctly.  It doesn't
actually drive hardware directly, but calls other drivers and uses
a real-time task to emulate commands for drivers and devices that
are incapable of native commands.  Thus, you can get accurately
timed I/O on any device.

Since the timing is all done in software, sampling jitter is much
higher than with a device that has an on-board timer, and maximum
sample rate is much lower.

Configuration options:
  [0] - minor number of device you wish to emulate commands for
  [1] - subdevice number you wish to emulate commands for



Driver: comedi_test.o
Description: generates fake waveforms
Author: Joachim Wuttke <Joachim.Wuttke@icn.siemens.de>, Frank Mori Hess
  <fmhess@uiuc.edu>, ds
Devices:
Status: works
Updated: Sat, 16 Mar 2002 17:34:48 -0800

This driver is mainly for testing purposes, but can also be used to
generate sample waveforms on systems that don't have data acquisition
hardware.

Configuration options:
  [0] - Amplitude in microvolts for fake waveforms (default 1 volt)
  [1] - Period in microseconds for fake waveforms (default 0.1 sec)

Generates a sawtooth wave on channel 0, square wave on channel 1, additional
waveforms could be added to other channels (currently they return flatline
zero volts).




Driver: contec_pci_dio.o
Description: Driver for Contec PIO1616L digital io board
Devices: [Contec] PIO1616L (contec_pci_dio)
Author: Stefano Rivoir <s.rivoir@gts.it>
Updated: Mon, 18 Mar 2002 15:34:01 -0800
Status: works

Configuration Options:
  none



Driver: daqboard2000.o
Description: IOTech DAQBoard/2000
Author: Anders Blomdell <anders.blomdell@control.lth.se>
Status: works
Devices: [IOTech] DAQBoard/2000 (daqboard2000)

Much of the functionality of this driver was determined from reading
the source code for the Windows driver.

The FPGA on the board requires initialization code, which can either
be compiled into the driver or loaded by comedi_config using the -i
option.  The latter is recommended, in order to save a bit of kernel
memory.

Configuration options:
  [0] - pointer to FPGA initialization data
          The pointer and size options are handled automatically
          by comedi_config when you use the -i option.
  [1] - size of FPGA data



Driver: das08.o
Description: DAS-08 compatible boards
Author: Warren Jasper, ds, Frank Hess
Devices: [ComputerBoards] DAS08 (das08), DAS08-PGM (das08-pgm),
  DAS08-PGH (das08-pgh), DAS08-PGL (das08-pgl), DAS08-AOH (das08-aoh),
  DAS08-AOL (das08-aol), DAS08-AOM (das08-aom), DAS08/JR-AO (das08/jr-ao),
  DAS08/JR-16-AO (das08jr-16-ao), PCI-DAS08 (pci-das08), PCM-DAS08 (pcm-das08),
  PC104-DAS08 (pc104-das08), DAS08/JR/16 (das08jr/16)
Status: works

This is a rewrite of the das08 and das08jr drivers.

Options (for ISA cards):
        [0] - base io address

Options (for pci-das08):
        [0] - bus  (optional)
        [1] = slot (optional)
Use the name 'pci-das08' for the pci-das08, NOT 'das08'.

Options (for pcm-das08):
        NONE

The das08 driver doesn't support asynchronous commands, since
the cheap das08 hardware doesn't really support them (except for
pcm-das08).  The
comedi_rt_timer driver can be used to emulate commands for this
driver.



Driver: das16.o
Description: DAS16 compatible boards
Author: Sam Moore, Warren Jasper, ds, Chris Baugher, Frank Hess, Roman Fietze
Devices: [Keithley Metrabyte] DAS-16 (das-16), DAS-16G (das-16g),
  DAS-16F (das-16f), DAS-1201 (das-1201), DAS-1202 (das-1202),
  DAS-1401 (das-1401), DAS-1402 (das-1402), DAS-1601 (das-1601),
  DAS-1602 (das-1602),
  [ComputerBoards] PC104-DAS16/JR (pc104-das16jr),
  PC104-DAS16JR/16 (pc104-das16jr/16),
  CIO-DAS16JR/16 (cio-das16jr/16),
  CIO-DAS16/JR (cio-das16/jr), CIO-DAS1401/12 (cio-das1401/12),
  CIO-DAS1402/12 (cio-das1402/12), CIO-DAS1402/16 (cio-das1402/16),
  CIO-DAS1601/12 (cio-das1601/12), CIO-DAS1602/12 (cio-das1602/12),
  CIO-DAS1602/16 (cio-das1602/16), CIO-DAS16/330 (cio-das16/330)
Status: works
Updated: 2002-04-17

A rewrite of the das16 and das1600 drivers.
Options:
	[0] - base io address
	[1] - irq (optional)
	[2] - dma (optional)
	[3] - master clock speed in MHz (optional, 1 or 10, ignored if
		board can probe clock, defaults to 1)
	[4] - analog input range lowest voltage in microvolts (optional,
		only useful if your board does not have software
		programmable gain)
	[5] - analog input range highest voltage in microvolts (optional,
		only useful if board does not have software programmable
		gain)
	[6] - analog output range lowest voltage in microvolts (optional)
	[7] - analog output range highest voltage in microvolts (optional)
	[8] - use timer mode for DMA, needed e.g. for buggy DMA controller
		in NS CS5530A (Geode Companion).  If set, also allows
		comedi_command() to be run without an irq.

Passing a zero for an option is the same as leaving it unspecified.

Both a dma channel and an irq (or use of 'timer mode', option 8) are required
for timed or externally triggered conversions.



Driver: das16m1.o
Description: CIO-DAS16/M1
Author: Frank Mori Hess <fmhess@uiuc.edu>
Devices: [MeasurementComputing] CIO-DAS16/M1 (cio-das16/m1)
Status: works

This driver supports a single board - the CIO-DAS16/M1.
As far as I know, there are no other boards that have
the same register layout.  Even the CIO-DAS16/M1/16 is
significantly different.

I was _barely_ able to reach the full 1 MHz capability
of this board, using a hard real-time interrupt
(set the TRIG_RT flag in your comedi_cmd and use
rtlinux or RTAI).  The board can't do dma, so the bottleneck is
pulling the data across the ISA bus.  I timed the interrupt
handler, and it took my computer ~470 microseconds to pull 512
samples from the board.  So at 1 Mhz sampling rate,
expect your CPU to be spending almost all of its
time in the interrupt handler.

This board has some unusual restrictions for its channel/gain list.  If the
list has 2 or more channels in it, then two conditions must be satisfied:
(1) - even/odd channels must appear at even/odd indices in the list
(2) - the list must have an even number of entries.

Options:
        [0] - base io address
        [1] - irq (optional, but you probably want it)

irq can be omitted, although the cmd interface will not work without it.



Driver: das1800.o
Description: Keithley Metrabyte DAS1800 (& compatibles)
Author: Frank Mori Hess <fmhess@uiuc.edu>
Devices: [Keithley Metrabyte] DAS-1701ST (das-1701st),
  DAS-1701ST-DA (das-1701st-da), DAS-1701/AO (das-1701ao),
  DAS-1702ST (das-1702st), DAS-1702ST-DA (das-1702st-da),
  DAS-1702HR (das-1702hr), DAS-1702HR-DA (das-1702hr-da),
  DAS-1702/AO (das-1702ao), DAS-1801ST (das-1801st),
  DAS-1801ST-DA (das-1801st-da), DAS-1801HC (das-1801hc),
  DAS-1801AO (das-1801ao), DAS-1802ST (das-1802st),
  DAS-1802ST-DA (das-1802st-da), DAS-1802HR (das-1802hr),
  DAS-1802HR-DA (das-1802hr-da), DAS-1802HC (das-1802hc),
  DAS-1802AO (das-1802ao)
Status: works

The waveform analog output on the 'ao' cards is not supported.
If you need it, send me (Frank Hess) an email.

Configuration options:
  [0] - I/O port base address
  [1] - IRQ (optional, required for timed or externally triggered conversions)
  [2] - DMA0 (optional, requires irq)
  [3] - DMA1 (optional, requires irq and dma0)



Driver: das6402.o
Description: Keithley Metrabyte DAS6402 (& compatibles)
Author: Oystein Svendsen <svendsen@pvv.org>
Status: bitrotten
Devices: [Keithley Metrabyte] DAS6402 (das6402)

This driver has suffered bitrot.



Driver: das800.o
Description: Keithley Metrabyte DAS800 (& compatibles)
Author: Frank Mori Hess <fmhess@uiuc.edu>
Devices: [Keithley Metrabyte] DAS-800 (das-800), DAS-801 (das-801),
  DAS-802 (das-802),
  [Measurement Computing] CIO-DAS800 (cio-das800),
  CIO-DAS801 (cio-das801), CIO-DAS802 (cio-das802),
  CIO-DAS802/16 (cio-das802/16)
Status: works, cio-das802/16 untested - email me if you have tested it

Configuration options:
  [0] - I/O port base address
  [1] - IRQ (optional, required for timed or externally triggered conversions)

Notes:
	IRQ can be omitted, although the cmd interface will not work without it.

	All entries in the channel/gain list must use the same gain and be
	consecutive channels counting upwards in channel number (these are
	hardware limitations.)

	I've never tested the gain setting stuff since I only have a
	DAS-800 board with fixed gain.

	The cio-das802/16 does not have a fifo-empty status bit!  Therefore
	only fifo-half-full transfers are possible with this card.



Driver: dt2801.o
Description: Data Translation DT2801 series and DT01-EZ
Author: ds
Status: works
Devices: [Data Translation] DT2801 (dt2801), DT2801-A, DT2801/5716A,
  DT2805, DT2805/5716A, DT2808, DT2818, DT2809, DT01-EZ

This driver can autoprobe the type of board.

Configuration options:
  [0] - I/O port base address
  [1] - unused
  [2] - A/D reference 0=differential, 1=single-ended
  [3] - A/D range
          0 = [-10,10]
	  1 = [0,10]
  [4] - D/A 0 range
          0 = [-10,10]
	  1 = [-5,5]
	  2 = [-2.5,2.5]
	  3 = [0,10]
	  4 = [0,5]
  [5] - D/A 1 range (same choices)



Driver: dt2811.o
Description: Data Translation DT2811
Author: ds
Devices: [Data Translation] DT2811-PGL (dt2811-pgl), DT2811-PGH (dt2811-pgh)
Status: works

Configuration options:
  [0] - I/O port base address
  [1] - IRQ, although this is currently unused
  [2] - A/D reference
          0 = signle-ended
          1 = differential
	  2 = pseudo-differential (common reference)
  [3] - A/D range
          0 = [-5,5]
	  1 = [-2.5,2.5]
	  2 = [0,5]
  [4] - D/A 0 range (same choices)
  [4] - D/A 1 range (same choices)



Driver: dt2814.o
Description: Data Translation DT2814
Author: ds
Status: complete
Devices: [Data Translation] DT2814 (dt2814)

Configuration options:
  [0] - I/O port base address
  [1] - IRQ

This card has 16 analog inputs multiplexed onto a 12 bit ADC.  There
is a minimally useful onboard clock.  The base frequency for the
clock is selected by jumpers, and the clock divider can be selected
via programmed I/O.  Unfortunately, the clock divider can only be
a power of 10, from 1 to 10^7, of which only 3 or 4 are useful.  In
addition, the clock does not seem to be very accurate.



Driver: dt2815.o
Description: Data Translation DT2815
Author: ds
Status: mostly complete, untested
Devices: [Data Translation] DT2815 (dt2815)

I'm not sure anyone has ever tested this board.  If you have information
contrary, please update.

Configuration options:
  [0] - I/O port base base address
  [1] - IRQ (unused)
  [2] - Voltage unipolar/bipolar configuration
          0 == unipolar 5V  (0V -- +5V)
	  1 == bipolar 5V  (-5V -- +5V)
  [3] - Current offset configuration
          0 == disabled  (0mA -- +32mAV)
          1 == enabled  (+4mA -- +20mAV)
  [4] - Firmware program configuration
          0 == program 1 (see manual table 5-4)
          1 == program 2 (see manual table 5-4)
          2 == program 3 (see manual table 5-4)
          3 == program 4 (see manual table 5-4)
  [5] - Analog output 0 range configuration
          0 == voltage
          1 == current
  [6] - Analog output 1 range configuration (same options)
  [7] - Analog output 2 range configuration (same options)
  [8] - Analog output 3 range configuration (same options)
  [9] - Analog output 4 range configuration (same options)
  [10] - Analog output 5 range configuration (same options)
  [11] - Analog output 6 range configuration (same options)
  [12] - Analog output 7 range configuration (same options)



Driver: dt2817.o
Description: Data Translation DT2817
Author: ds
Status: complete
Devices: [Data Translation] DT2817 (dt2817)

A very simple digital I/O card.  Four banks of 8 lines, each bank
is configurable for input or output.  One wonders why it takes a
50 page manual to describe this thing.

The driver (which, btw, is much less than 50 pages) has 1 subdevice
with 32 channels, configurable in groups of 8.

Configuration options:
  [0] - I/O port base base address



Driver: dt282x.o
Description: Data Translation DT2821 series (including DT-EZ)
Author: ds
Devices: [Data Translation] DT2821 (dt2821), DT2823 (dt2823),
  DT2824-PGH (dt2824-pgh), DT2824-PGL (dt2824-pgl), DT2825 (dt2825),
  DT2827 (dt2827), DT2828 (dt2828), DT21-EZ (dt21-ez), DT23-EZ (dt23-ez),
  DT24-EZ (dt24-ez), DT24-EZ-PGL (dt24-ez-pgl)
Status: complete
Updated: Wed, 22 Aug 2001 17:11:34 -0700

Configuration options:
  [0] - I/O port base address
  [1] - IRQ
  [2] - DMA 1
  [3] - DMA 2
  [4] - AI jumpered for 0=single ended, 1=differential
  [5] - AI jumpered for 0=straight binary, 1=2's complement
  [6] - AO 0 jumpered for 0=straight binary, 1=2's complement
  [7] - AO 1 jumpered for 0=straight binary, 1=2's complement
  [8] - AI jumpered for 0=[-10,10]V, 1=[0,10], 2=[-5,5], 3=[0,5]
  [9] - AO 0 jumpered for 0=[-10,10]V, 1=[0,10], 2=[-5,5], 3=[0,5],
        4=[-2.5,2.5]
  [10]- A0 1 jumpered for 0=[-10,10]V, 1=[0,10], 2=[-5,5], 3=[0,5],
        4=[-2.5,2.5]

Notes:
  - AO commands might be broken.
  - If you try to run a command on both the AI and AO subdevices
    simultaneously, bad things will happen.  The driver needs to
    be fixed to check for this situation and return an error.



Driver: dt3000.o
Description: Data Translation DT3000 series
Author: ds
Devices: [Data Translation] DT3001 (dt3000), DT3001-PGL, DT3002, DT3003,
  DT3003-PGL, DT3004, DT3005, DT3004-200
Status: works

There is code to support AI commands, but it may not work.

AO commands are not supported.



Driver: fl512.o
Description: unknown
Author: unknown
Devices: [unknown] FL512 (fl512)
Status: unknown

Digital I/O is not supported.

Configuration options:
  [0] - I/O port base address



Driver: icp_multi.o
Description: Inova ICP_MULTI
Author: Anne Smorthit <anne.smorthit@sfwte.ch>
Devices: [Inova] ICP_MULTI (icp_multi)
Status: unknown

Options:
 [0] - PCI bus number - if bus number and slot number are 0, 
                        then driver search for first unused card
 [1] - PCI slot number 



Driver: ii_pci20kc.o
Description: Intelligent Instruments PCI-20001C carrier board
Author: Markus Kempf <kempf@matsci.uni-sb.de>
Devices: [Intelligent Instrumentation] PCI-20001C (ii_pci20kc)
Status: works

Supports the PCI-20001 C-2a Carrier board, and could probably support
the other carrier boards with small modifications.  Modules supported
are:
	PCI-20006 M-2 16-bit analog output module
	PCI-20341 M-1A 16-bit analog input module

Options:
  0   Board base address
  1   IRQ
  2   first option for module 1
  3   second option for module 1
  4   first option for module 2
  5   second option for module 2
  6   first option for module 3
  7   second option for module 3

options for PCI-20006M:
  first:   Analog output channel 0 range configuration
             0  bipolar 10  (-10V -- +10V)
             1  unipolar 10  (0V -- +10V)
             2  bipolar 5  (-5V -- 5V)
  second:  Analog output channel 1 range configuration

options for PCI-20341M:
  first:   Analog input gain configuration
             0  1
             1  10
             2  100
             3  200



Driver: ke_counter.o
Description: Driver for Kolter Electronic Counter Card
Devices: (Kolter Electronic) PCI Counter Card [ke_counter]
Author: mh
Updated: 11.4.2002
Status: tested

This driver is a simple driver to read the counter values from
Kolter Electronic PCI Counter Card.



Driver: me_daq.o
Description: Driver for the Meilhaus PCI data acquisition cards.
Author: Michael Hillmann <hillmann@syscongroup.de>
Devices: [Meilhaus] ME-2600i, ME-2000i (me_daq)
Status: experimental

Supports:

    Analog Output

Configuration options:

    [0] - PCI bus number (optional)
    [1] - PCI slot number (optional)

    If bus/slot is not specified, the first available PCI
    device will be used.



Driver: mpc8260cpm.o
Description: MPC8260 CPM module generic digital I/O lines
Devices: [Motorola] MPC8260 CPM (mpc8260cpm)
Author: ds
Status: experimental
Updated: Sat, 16 Mar 2002 17:34:48 -0800

This driver is specific to the Motorola MPC8260 processor, allowing
you to access the processor's generic digital I/O lines.

It is apparently missing some code.



Driver: multiq3.o
Description: Quanser Consulting MultiQ-3
Author: Anders Blomdell <anders.blomdell@control.lth.se>
Status: works
Devices: [Quanser Consulting] MultiQ-3 (multiq3)




Driver: ni_670x.o
Description: National Instruments 670x
Author: Bart Joris <bjoris@advalvas.be>
Updated: Wed, 22 Aug 2001 22:47:32 -0700
Devices: [National Instruments] PCI-6703 (ni_670x), PCI-6704
Status: unknown

The driver currently does not recognize the 6704, because the PCI
ID is not known.

Commands are not supported.



Driver: ni_at_a2150.o
Description: National Instruments AT-A2150
Author: Frank Mori Hess
Status: works
Devices: [National Instruments] AT-A2150C (at_a2150c), AT-2150S (at_a2150s)

If you want to ac couple the board's inputs, use AREF_OTHER.

Configuration options:
  [0] - I/O port base address
  [1] - IRQ (optional, required for timed conversions)
  [2] - DMA (optional, required for timed conversions)




Driver: ni_at_ao.o
Description: National Instruments AT-AO-6/10
Devices: [National Instruments] AT-AO-6 (at-ao-6), AT-AO-10 (at-ao-10)
Status: untested
Author: ds
Updated: Fri,  7 Jun 2002 13:20:30 -0700

This driver has not been tested, but should work.




Driver: ni_atmio.o
Description: National Instruments AT-MIO-E series
Author: ds
Devices: [National Instruments] AT-MIO-16E-1 (ni_atmio),
  AT-MIO-16E-2, AT-MIO-16E-10, AT-MIO-16DE-10, AT-MIO-64E-3,
  AT-MIO-16XE-50, AT-MIO-16XE-10, AT-AI-16XE-10
Status: works
Updated: Sat, 16 Mar 2002 17:34:48 -0800

The isapnptools package is required to use this board.  Use isapnp to
configure the I/O base for the board, and then pass the same value as
a parameter in comedi_config.  A sample isapnp.conf file is included
in the etc/ directory of Comedilib.

Comedilib includes a utility to autocalibrate these boards.  The
boards seem to boot into a state where the all calibration DACs
are at one extreme of their range, thus the default calibration
is terrible.  Calibration at boot is strongly encouraged.

To use the extended digital I/O on some of the boards, enable the
8255 driver when configuring the Comedi source tree.

External triggering is supported for some events.  The channel index
(scan_begin_arg, etc.) maps to PFI0 - PFI9.

Some of the more esoteric triggering possibilities of these boards
are not supported.



Driver: ni_atmio16d.o
Description: National Instruments AT-MIO-16D
Author: Chris R. Baugher <baugher@enteract.com>
Status: unknown
Devices: [National Instruments] AT-MIO-16 (atmio16), AT-MIO-16D (atmio16d)



Driver: ni_daq_dio24.o
Description: National Instruments PCMCIA DAQ-Card DIO-24
Author: Daniel Vecino Castel <dvecino@able.es>
Devices: National Instruments PCMCIA DAQ-Card DIO-24
Status: ?



Driver: ni_labpc.o
Description: National Instruments Lab-PC (& compatibles)
Author: Frank Mori Hess <fmhess@users.sourceforge.net>
Devices: [National Instruments] DAQCard-1200 (daqcard-1200), Lab-PC-1200 (labpc-1200),
  Lab-PC-1200AI (labpc-1200ai), Lab-PC+ (lab-pc+), PCI-1200 (pci-1200)
Status: works

Tested with lab-pc-1200.  For the older Lab-PC+, not all input ranges
and analog references will work, the available ranges/arefs will
depend on how you have configured the jumpers on your board
(see your owner's manual).

Configuration options - ISA boards:
  [0] - I/O port base address
  [1] - IRQ (optional, required for timed or externally triggered conversions)
  [2] - DMA channel (optional)

Configuration options - PCI boards:
  [0] - bus (optional)
  [1] - slot (optional)

Configuration options - PCMCIA boards:
  none

Lab-pc+ has quirky chanlist when scanning multiple channels.  Scan
sequence must start at highest channel, then decrement down to
channel 0.  1200 series cards can scan down like lab-pc+ or scan
up from channel zero.




Driver: ni_mio_cs.o
Description: National Instruments DAQCard E series
Author: ds
Status: works
Devices: [National Instruments] DAQCard-AI-16XE-50 (ni_mio_cs),
  DAQCard-AI-16E-4, DAQCard-6062E, DAQCard-6024E

See the notes in the ni_atmio.o driver.



Driver: ni_pcidio.o
Description: National Instruments PCI-DIO32HS, PCI-DIO96, PCI-6533, PCI-6503
Author: ds
Status: works
Devices: [National Instruments] PCI-DIO-32HS (ni_pcidio), PXI-6533,
  PCI-DIO-96, PCI-DIO-96B, PXI-6508, PCI-6503, PCI-6503B, PCI-6503X,
  PXI-6503, PCI-6534, PCI-6533
Updated: Sun, 21 Apr 2002 21:03:38 -0700

The DIO-96 appears as four 8255 subdevices.  See the 8255
driver notes for details.

The DIO32HS board appears as one subdevice, with 32 channels.
Each channel is individually I/O configurable.  The channel order
is 0=A0, 1=A1, 2=A2, ... 8=B0, 16=C0, 24=D0.  The driver only
supports simple digital I/O; no handshaking is supported.

DMA mostly works for the PCI-DIO32HS, but only in timed input mode.

This driver could be easily modified to support AT-MIO32HS and
AT-MIO96.



Driver: ni_pcimio.o
Description: National Instruments PCI-MIO-E series (all boards)
Author: ds
Status: works
Devices: [National Instruments] PCI-MIO-16XE-50 (ni_pcimio),
  PCI-MIO-16XE-10, PXI-6030E, PCI-MIO-16E-1, PCI-MIO-16E-4, PCI-6040E,
  PXI-6040E, PCI-6031E, PCI-6032E, PCI-6033E, PCI-6071E, PCI-6023E,
  PCI-6024E, PCI-6025E, PXI-6025E, PCI-6034E, PCI-6035E, PCI-6052E,
  PCI-6110, PCI-6111, PCI-6711, PCI-6713, PXI-6071E, PXI-6070E,
  PXI-6052E, PCI-6036E, PCI-6731, PCI-6733
Updated: Sat, 16 Mar 2002 17:34:48 -0800

These boards are almost identical to the AT-MIO E series, except that
they use the PCI bus instead of ISA (i.e., AT).  See the notes for
the ni_atmio.o driver for additional information about these boards.

Autocalibration is supported on many of the devices, using the
calibration utility in Comedilib.

By default, the driver uses DMA to transfer analog input data to
memory.  When DMA is enabled, not all triggering features are
supported.

Streaming analog output is not supported on PCI-671x and PCI-673x.

PCI IDs are not known for PCI-6731 and PCI-6733.  Digital I/O may not
work on 673x.

Information (number of channels, bits, etc.) for some devices may be
incorrect.  Please check this and submit a bug if there are problems
for your device.

Bugs:
 - When DMA is enabled, COMEDI_EV_SCAN_END and COMEDI_EV_CONVERT do
   not work correctly.
 - There are reported problems with the 61xx and 67xx boards.




Driver: pcl711.o
Description: Advantech PCL-711 and 711b, ADLink ACL-8112
Author: ds, Janne Jalkanen <jalkanen@cs.hut.fi>, Eric Bunn <ebu@cs.hut.fi>
Status: mostly complete
Devices: [Advantech] PCL-711 (pcl711), PCL-711B (pcl711b),
  [AdLink] ACL-8112HG (acl8112hg), ACL-8112DG (acl8112dg)

Since these boards do not have DMA or FIFOs, only immediate mode is
supported.




Driver: pcl724.o
Description: Advantech PCL-724, PCL-722, PCL-731 ADLink ACL-7122, ACL-7124,
  PET-48DIO
Author: Michal Dobes <majkl@tesnet.cz>
Devices: [Advantech] PCL-724 (pcl724), PCL-722 (pcl722), PCL-731 (pcl731),
  [ADLink] ACL-7122 (acl7122), ACL-7124 (acl7124), PET-48DIO (pet48dio)
Status: untested

This is driver for digital I/O boards PCL-722/724/731 with 144/24/48 DIO
and for digital I/O boards ACL-7122/7124/PET-48DIO with 144/24/48 DIO.
It need 8255.o for operations and only immediate mode is supported.
See the source for configuration details.



Driver: pcl725.o
Description: Advantech PCL-725 (& compatibles)
Author: ds
Status: unknown
Devices: [Advantech] PCL-725 (pcl725)



Driver: pcl726.o
Description: Advantech PCL-726 & compatibles
Author: ds
Status: untested
Devices: [Advantech] PCL-726 (pcl726), PCL-727 (pcl727), PCL-728 (pcl728),
  [ADLink] ACL-6126 (acl6126), ACL-6128 (acl6128)

Interrupts are not supported.

    Options for PCL-726:
     [0] - IO Base
     [2]...[7] - D/A output range for channel 1-6: 
               0: 0-5V, 1: 0-10V, 2: +/-5V, 3: +/-10V, 
	       4: 4-20mA, 5: unknown (external reference)
	       
    Options for PCL-727:
     [0] - IO Base
     [2]...[13] - D/A output range for channel 1-12: 
               0: 0-5V, 1: 0-10V, 2: +/-5V, 
	       3: 4-20mA
	       
    Options for PCL-728 and ACL-6128:
     [0] - IO Base
     [2], [3] - D/A output range for channel 1 and 2: 
               0: 0-5V, 1: 0-10V, 2: +/-5V, 3: +/-10V, 
	       4: 4-20mA, 5: 0-20mA
	       
    Options for ACL-6126:
     [0] - IO Base
     [1] - IRQ (0=disable, 3, 5, 6, 7, 9, 10, 11, 12, 15) (currently ignored)
     [2]...[7] - D/A output range for channel 1-6: 
               0: 0-5V, 1: 0-10V, 2: +/-5V, 3: +/-10V, 
	       4: 4-20mA



Driver: pcl812.o
Description: Advantech PCL-812/PG, PCL-813/B,
             ADLink ACL-8112DG/HG/PG, ACL-8113, ACL-8216,
             ICP DAS A-821PGH/PGL/PGL-NDA, A-822PGH/PGL, A-823PGH/PGL, A-826PG,
             ICP DAS ISO-813
Author: Michal Dobes <majkl@tesnet.cz>
Devices: [Advantech] PCL-812 (pcl812), PCL-812PG (pcl812pg),
  PCL-813 (pcl813), PCL-813B (pcl813b), [ADLink] ACL-8112DG (acl8112dg),
  ACL-8112HG (acl8112hg), ACL-8113 (acl-8113), ACL-8216 (acl8216),
  [ICP] ISO-813 (iso813), A-821PGH (a821pgh), A-821PGL (a821pgl),
  A-821PGL-NDA (a821pclnda), A-822PGH (a822pgh), A-822PGL (a822pgl),
  A-823PGH (a823pgh), A-823PGL (a823pgl), A-826PG (a826pg)
Status: works (I hope. My board fire up under my hands
               and I cann't test all features.)

This driver supports insn and cmd interfaces. Some boards support only insn
becouse their hardware don't allow more (PCL-813/B, ACL-8113, ISO-813).
Data transfer over DMA is supported only when you measure only one
channel, this is too hardware limitation of these boards.
See the head of the source file pcl812.c for configuration options.



Driver: pcl816.o
Description: Advantech PCL-816 cards, PCL-814
Author: Juan Grigera <juan@grigera.com.ar>
Devices: [Advantech] PCL-816 (pcl816), PCL-814B (pcl814b)
Status: works
Updated: Tue,  2 Apr 2002 23:15:21 -0800

PCL 816 and 814B have 16 SE/DIFF ADCs, 16 DACs, 16 DI and 16 DO.
Differences are at resolution (16 vs 12 bits).

The driver support AI command mode, other subdevices not written.

Analog output and digital input and output are not supported.

Configuration Options:
  [0] - IO Base
  [1] - IRQ	(0=disable, 2, 3, 4, 5, 6, 7)
  [2] - DMA	(0=disable, 1, 3)
  [3] - 0, 10=10MHz clock for 8254
            1= 1MHz clock for 8254




Driver: pcl818.o
Description: Advantech PCL-818 cards, PCL-718
Author: Michal Dobes <majkl@tesnet.cz>
Devices: [Advantech] PCL-818L (pcl818l), PCL-818H (pcl818h),
  PCL-818HD (pcl818hd), PCL-818HG (pcl818hg), PCL-818 (pcl818),
  PCL-718 (pcl718)
Status: works

All cards have 16 SE/8 DIFF ADCs, one or two DACs, 16 DI and 16 DO.
Differences are only at maximal sample speed, range list and FIFO
support.
The driver support AI mode 0, 1, 3 other subdevices (AO, DI, DO) support
only mode 0. If DMA/FIFO/INT are disabled then AI support only mode 0.
PCL-818HD and PCL-818HG support 1kword FIFO. Driver support this FIFO
but this code is untested.
A word or two about DMA. Driver support DMA operations at two ways:
1) DMA uses two buffers and after one is filled then is generated
   INT and DMA restart with second buffer. With this mode I'm unable run
   more that 80Ksamples/secs without data dropouts on K6/233.
2) DMA uses one buffer and run in autoinit mode and the data are
   from DMA buffer moved on the fly with 2kHz interrupts from RTC.
   This mode is used if the interrupt 8 is available for allocation.
   If not, then first DMA mode is used. With this I can run at
   full speed one card (100ksamples/secs) or two cards with
   60ksamples/secs each (more is problem on account of ISA limitations).
   To use this mode you must have compiled  kernel with disabled
   "Enhanced Real Time Clock Support".
   Maybe you can have problems if you use xntpd or similar.
   If you've data dropouts with DMA mode 2 then:
    a) disable IDE DMA
    b) switch text mode console to fb.

   Options for PCL-818L:
    [0] - IO Base
    [1] - IRQ	(0=disable, 2, 3, 4, 5, 6, 7)
    [2] - DMA	(0=disable, 1, 3)
    [3] - 0, 10=10MHz clock for 8254
              1= 1MHz clock for 8254
    [4] - 0,  5=A/D input  -5V.. +5V
          1, 10=A/D input -10V..+10V
    [5] - 0,  5=D/A output 0-5V  (internal reference -5V)
          1, 10=D/A output 0-10V (internal reference -10V)
	  2    =D/A output unknow (external reference)
       
   Options for PCL-818, PCL-818H:
    [0] - IO Base
    [1] - IRQ	(0=disable, 2, 3, 4, 5, 6, 7)
    [2] - DMA	(0=disable, 1, 3)
    [3] - 0, 10=10MHz clock for 8254
              1= 1MHz clock for 8254
    [4] - 0,  5=D/A output 0-5V  (internal reference -5V)
          1, 10=D/A output 0-10V (internal reference -10V)
	  2    =D/A output unknow (external reference)

   Options for PCL-818HD, PCL-818HG:
    [0] - IO Base
    [1] - IRQ	(0=disable, 2, 3, 4, 5, 6, 7)
    [2] - DMA/FIFO  (-1=use FIFO, 0=disable both FIFO and DMA, 
                      1=use DMA ch 1, 3=use DMA ch 3)
    [3] - 0, 10=10MHz clock for 8254
              1= 1MHz clock for 8254
    [4] - 0,  5=D/A output 0-5V  (internal reference -5V)
          1, 10=D/A output 0-10V (internal reference -10V)
   	  2    =D/A output unknow (external reference)

   Options for PCL-718:
    [0] - IO Base
    [1] - IRQ	(0=disable, 2, 3, 4, 5, 6, 7)
    [2] - DMA	(0=disable, 1, 3)
    [3] - 0, 10=10MHz clock for 8254
              1= 1MHz clock for 8254
    [4] -     0=A/D Range is +/-10V
	      1=             +/-5V
	      2=             +/-2.5V
	      3=             +/-1V
	      4=             +/-0.5V 
	      5=  	     user defined bipolar
	      6=	     0-10V
	      7=	     0-5V
 	      8=	     0-2V
	      9=	     0-1V
	     10=	     user defined unipolar
    [5] - 0,  5=D/A outputs 0-5V  (internal reference -5V)
          1, 10=D/A outputs 0-10V (internal reference -10V)
	      2=D/A outputs unknow (external reference)
    [6] - 0, 60=max  60kHz A/D sampling
          1,100=max 100kHz A/D sampling (PCL-718 with Option 001 installed)




Driver: pcm3730.o
Description: PCM3730
Author: Blaine Lee
Devices: [Advantech] PCM-3730 (pcm3730)
Status: unknown

Configuration options:
  [0] - I/O port base



Driver: pcmad.o
Description: Winsystems PCM-A/D12, PCM-A/D16
Author: ds
Devices: [Winsystems] PCM-A/D12 (pcmad12), PCM-A/D16 (pcmad16)
Status: untested

This driver was written on a bet that I couldn't write a driver
in less than 2 hours.  I won the bet, but never got paid.  =(

Configuration options:
  [0] - I/O port base
  [1] - unused
  [2] - Analog input reference
          0 = single ended
          1 = differential
  [3] - Analog input encoding (must match jumpers)
          0 = straight binary
          1 = two's complement



Driver: poc.o
Description: Generic driver for very simple devices
Device names: dac02
Author: ds
Devices: [Keithley Metrabyte] DAC-02 (dac02), [Advantech] PCL-733 (pcl733),
  PCL-734 (pcl734)
Updated: Sat, 16 Mar 2002 17:34:48 -0800
Status: unknown

This driver is indended to support very simple ISA-based devices,
including:
  dac02 - Keithley DAC-02 analog output board
  pcl733 - Advantech PCL-733
  pcl734 - Advantech PCL-734

Configuration options:
  [0] - I/O port base



Driver: quatech_daqp_cs.o
Description: Quatech DAQP PCMCIA data capture cards
Author: Brent Baccala <baccala@freesoft.org>
Status: unkown
Devices: [Quatech] DAQP-208 (daqp), DAQP-308



Driver: rtd520.o
Description: Real Time Devices PCI4520/DM7520
Author: Dan Christian
Devices: [Real Time Devices] DM7520HR-1 (DM7520), DM7520HR-8 (DM7520-8),
  PCI4520 (PCI4520), PCI4520-8 (PCI4520-8)
Status: Works.  Only tested on DM7520-8.  Not SMP safe.

Configuration options:
  [0] - PCI bus of device (optional)
          If bus/slot is not specified, the first available PCI
          device will be used.
  [1] - PCI slot of device (optional)



Driver: rti800.o
Description: Analog Devices RTI-800/815
Author: ds
Status: unknown
Devices: [Analog Devices] RTI-800 (rti800), RTI-815 (rti815)

Configuration options:
  [0] - I/O port base address
  [1] - IRQ
  [2] - A/D reference
          0 = differential
          1 = pseudodifferential (common)
          2 = single-ended
  [3] - A/D range
          0 = [-10,10]
          1 = [-5,5]
          2 = [0,10]
  [4] - A/D encoding
          0 = two's complement
          1 = straight binary
  [5] - DAC 0 range
          0 = [-10,10]
          1 = [0,10]
  [5] - DAC 0 encoding
          0 = two's complement
          1 = straight binary
  [6] - DAC 1 range (same as DAC 0)
  [7] - DAC 1 encoding (same as DAC 0)



Driver: rti802.o
Description: Analog Devices RTI-802
Author: Anders Blomdell <anders.blomdell@control.lth.se>
Devices: [Analog Devices] RTI-802 (rti802)
Status: works

Configuration Options:
    [0] - i/o base
    [1] - unused
    [2] - dac#0  0=two's comp, 1=straight
    [3] - dac#0  0=bipolar, 1=unipolar
    [4] - dac#1 ...
    ...
    [17] - dac#7 ...



Driver: serial2002.o
Description: Driver for serial connected hardware
Devices:
Author: Anders Blomdell
Updated: Fri,  7 Jun 2002 12:56:45 -0700
Status: in development




Driver: skel.o
Description: Skeleton driver, an example for driver writers
Devices:
Author: ds
Updated: Mon, 18 Mar 2002 15:34:01 -0800
Status: works

This driver is a documented example on how Comedi drivers are
written.

Configuration Options:
  none



Driver: ssv_dnp.o
Description: SSV Embedded Systems DIL/Net-PC
Author: Robert Schwebel <robert@schwebel.de>
Devices: [SSV Embedded Systems] DIL/Net-PC 1486 (dnp-1486)
Status: unknown



