#
#   "SystemImager"
#
#   $Id: screencaptured_multicast_install.txt 2859 2004-09-12 04:45:27Z brianfinley $
#
#   This is a serial console capture of a multicast install.  It was captured
#   in the fall of 2003 and has been in captivity ever since for observational
#   purposes.  -BEF-
#
Linux version 2.4.20-boel (dannf@jale) (gcc version 3.3.1 20030626 (Debian prerelease)) #1 SMP Mon Jul 14 22:31:50 MDT 2003
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 00000000d7ff0000 (usable)
 BIOS-e820: 00000000d7ff0000 - 00000000d7ff3000 (ACPI NVS)
 BIOS-e820: 00000000d7ff3000 - 00000000d8000000 (ACPI data)
 BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
Warning only 896MB will be used.
Use a HIGHMEM enabled kernel.
896MB LOWMEM available.
found SMP MP-table at 000f54b0
hm, page 000f5000 reserved twice.
hm, page 000f6000 reserved twice.
hm, page 000f1000 reserved twice.
hm, page 000f2000 reserved twice.
On node 0 totalpages: 229376
zone(0): 4096 pages.
zone(1): 225280 pages.
zone(2): 0 pages.
ACPI: Searched entire block, no RSDP was found.
ACPI: RSDP located at physical address c00f75c0
RSD PTR  v0 [MSISYS]
__va_range(0xd7ff3000, 0x68): idx=32 mapped at fffde000
ACPI table found: RSDT v1 [MSISYS AWRDACPI 16944.11825]
__va_range(0xd7ff3040, 0x24): idx=32 mapped at fffde000
__va_range(0xd7ff3040, 0x74): idx=32 mapped at fffde000
ACPI table found: FACP v1 [MSISYS AWRDACPI 16944.11825]
__va_range(0xd7ff69c0, 0x24): idx=32 mapped at fffde000
__va_range(0xd7ff69c0, 0x6c): idx=32 mapped at fffde000
ACPI table found: APIC v1 [MSISYS AWRDACPI 16944.11825]
__va_range(0xd7ff69c0, 0x6c): idx=32 mapped at fffde000
LAPIC (acpi_id[0x0000] id[0x0] enabled[1])
CPU 0 (0x0000) enabledProcessor #0 Pentium 4(tm) XEON(tm) APIC version 16

LAPIC (acpi_id[0x0001] id[0x6] enabled[1])
CPU 1 (0x0600) enabledProcessor #6 Pentium 4(tm) XEON(tm) APIC version 16

LAPIC (acpi_id[0x0002] id[0x1] enabled[0])
CPU 2 (0x0100) disabled
LAPIC (acpi_id[0x0003] id[0x7] enabled[0])
CPU 3 (0x0700) disabled
IOAPIC (id[0x2] address[0xfec00000] global_irq_base[0x0])
INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x0] trigger[0x0])
INT_SRC_OVR (bus[0] irq[0x9] global_irq[0x9] polarity[0x1] trigger[0x3])
4 CPUs total
Local APIC address fee00000
Enabling the CPU's according to the ACPI table
Intel MultiProcessor Specification v1.4
    Virtual Wire compatibility mode.
OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
I/O APIC #2 Version 17 at 0xFEC00000.
Enabling APIC mode: Flat.	Using 1 I/O APICs
Processors: 2
IBM machine detected. Enabling interrupts during APM calls.
Kernel command line: load_ramdisk=1 initrd=xcat/systemimager/x86/initrd.img root=/dev/ram rw ramdisk_blocksize=4096 console=ttyS1,57600 BOOT_IMAGE=xcat/systemimager/x86/kernel 
Initializing CPU#0
Detected 2379.072 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 4744.80 BogoMIPS
Memory: 904256k/917504k available (1159k kernel code, 12864k reserved, 350k data, 512k init, 0k highmem)
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode cache hash table entries: 65536 (order: 7, 524288 bytes)
Mount-cache hash table entries: 16384 (order: 5, 131072 bytes)
Buffer-cache hash table entries: 65536 (order: 6, 262144 bytes)
Page-cache hash table entries: 262144 (order: 8, 1048576 bytes)
CPU: L1 I cache: 0K, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
CPU: L1 I cache: 0K, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU0: Intel(R) Xeon(TM) CPU 2.40GHz stepping 07
per-CPU timeslice cutoff: 1462.70 usecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Booting processor 1/6 eip 2000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 4757.91 BogoMIPS
CPU: L1 I cache: 0K, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 3
CPU1: Intel(R) Xeon(TM) CPU 2.40GHz stepping 07
Total of 2 processors activated (9502.72 BogoMIPS).
WARNING: No sibling found for CPU 0.
WARNING: No sibling found for CPU 1.
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
..TIMER: vector=0x31 pin1=2 pin2=0
testing the IO APIC.......................

.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2379.0628 MHz.
..... host bus clock speed is 99.1275 MHz.
cpu: 0, clocks: 991275, slice: 330425
CPU0<T0:991264,T1:660832,D:7,S:330425,C:991275>
cpu: 1, clocks: 991275, slice: 330425
CPU1<T0:991264,T1:330400,D:14,S:330425,C:991275>
checking TSC synchronization across CPUs: passed.
Waiting on wait_init_idle (map = 0x2)
All processors have done init_idle
PCI: PCI BIOS revision 2.10 entry at 0xfaf60, last bus=4
PCI: Using configuration type 1
PCI: Probing PCI hardware
Transparent bridge - Intel Corp. 82801BA/CA/DB PCI Bridge
PCI: Using IRQ router PIIX [8086/2440] at 00:1f.0
PCI->APIC IRQ transform: (B0,I31,P3) -> 19
PCI->APIC IRQ transform: (B0,I31,P1) -> 17
PCI->APIC IRQ transform: (B0,I31,P1) -> 17
PCI->APIC IRQ transform: (B1,I0,P0) -> 22
PCI->APIC IRQ transform: (B3,I1,P0) -> 20
PCI->APIC IRQ transform: (B3,I1,P1) -> 20
PCI->APIC IRQ transform: (B3,I8,P0) -> 20
PCI->APIC IRQ transform: (B4,I10,P0) -> 18
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
pty: 256 Unix98 ptys configured
keyboard: Timeout - AT keyboard not present?(ed)
keyboard: Timeout - AT keyboard not present?(f4)
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH2: IDE controller on PCI bus 00 dev f9
ICH2: detected chipset, but driver not compiled in!
ICH2: chipset revision 4
ICH2: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:pio
hdc: LTN486S, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
ide-floppy driver 0.99.newide
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 8192K size 4096 blocksize
loop: loaded (max 8 devices)
Intel(R) PRO/1000 Network Driver - version 4.4.12-k1
Copyright (c) 1999-2002 Intel Corporation.
eth0: Intel(R) PRO/1000 Network Connection
pcnet32.c:v1.27b 01.10.2002 tsbogend@alpha.franken.de
ns83820.c: National Semiconductor DP83820 10/100/1000 driver.
sk98lin: No adapter found.
ide-floppy driver 0.99.newide
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 488k freed
VFS: Mounted root (cramfs filesystem).
Mounted devfs on /dev
Freeing unused kernel memory: 512k freed
serial console detected.  Disabling virtual terminals.
init started:  BusyBox v0.60.3 (2003.07.15-04:57+0000) multi-call binary

get_arch

mount_proc

switch_root_to_tmpfs

mount_dev_on_devfs
Started device management daemon v1.3.25 for /dev

mount_proc

adjust_arch

ifconfig_loopback

load_my_modules

read_local_cfg
Checking for floppy diskette.
YOU MAY SEE SOME "wrong magic" ERRORS HERE, AND THAT IS NORMAL.
end_request: I/O error, dev 02:00 (floppy), sector 0
end_request: I/O error, dev 02:00 (floppy), sector 0
end_request: I/O error, dev 02:00 (floppy), sector 0
No floppy diskette in drive.

start_network
IP Address not set by local.cfg.  I will use DHCP.

sleep 0:  This is to give your switch (if you're using one) time to
           recognize your ethernet card before we try the network.
           Tip: You can use <ctrl>+<c> to pass the time (pun intended).




dhclient
Internet Software Consortium DHCP Client 2.0pl5
Copyright 1995, 1996, 1997, 1998, 1999 The Internet Software Consortium.
All rights reserved.

Please contribute if you find this software useful.
For info, please visit http://www.isc.org/dhcp-contrib.html

e1000: eth0 NIC Link is Up 1000 Mbps Full Duplex
Listening on LPF/eth0/00:02:b3:ac:7d:df
Sending on   LPF/eth0/00:02:b3:ac:7d:df
Listening on LPF/lo/<null>
Sending on   LPF/lo/<null>
Sending on   Socket/fallback/fallback-net
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4
DHCPDISCOVER on lo to 255.255.255.255 port 67 interval 8
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4
DHCPOFFER from 192.5.198.221
DHCPDISCOVER on lo to 255.255.255.255 port 67 interval 15
DHCPREQUEST on eth0 to 255.255.255.255 port 67
DHCPACK from 192.5.198.221
Using DHCP server (very deprecated) as IMAGESERVER: 192.5.198.221
bound to 192.5.198.95 -- renewal in 43200 seconds.

ping_test

Pinging image server "192.5.198.221"
to ensure we have network connectivity.

PING ATTEMPT 1: 
PING 192.5.198.221 (192.5.198.221): 56 data bytes
64 bytes from 192.5.198.221: icmp_seq=0 ttl=64 time=0.7 ms

--- 192.5.198.221 ping statistics ---
1 packets transmitted, 1 packets received, 0% packet loss
round-trip min/avg/max = 0.7/0.7/0.7 ms

  We have connectivity to the Image Server!

start_syslogd

Using multicast...
get_flamethrower_directory

flamethrower_client(flamethrower_directory)
--------------------------------------------------------------------------------
udp-receiver --interface eth0 --portbase 9000 2>/tmp/udp-receiver.flamethrower_directory | tar -x -C /var/lib/systemimager/flamethrower 2>/tmp/tar.stderr.log
...done!
flamethrower_client: Success!
--------------------------------------------------------------------------------

get_boel_binaries_tarball

flamethrower_client(boot-i386-standard)
--------------------------------------------------------------------------------
udp-receiver --interface eth0 --portbase 9006 --nosync 2>/tmp/udp-receiver.boot-i386-standard | tar -x -C /tmp/boel_binaries 2>/tmp/tar.stderr.log
...done!
flamethrower_client: Success!
--------------------------------------------------------------------------------

get_scripts_directory

flamethrower_client(autoinstall_scripts)
--------------------------------------------------------------------------------
udp-receiver --interface eth0 --portbase 9002 --nosync 2>/tmp/udp-receiver.autoinstall_scripts | tar --overwrite -xp -C /scripts 2>/tmp/tar.stderr.log
...done!
flamethrower_client: Success!
--------------------------------------------------------------------------------

autodetect_hardware_and_load_modules
Detecting hardware: agpgart agpgart aic7xxx aic7xxx ide-scsi usb-uhcSCSI subsystem driver Revision: 1.00
i

Loading sd_mod...
Using /lib/modules/2.4.20-boel/kernel/drivers/scsi/scsi_mod.o
Using /lib/modules/2.4.20-boel/kernel/drivers/scsi/sd_mod.o

Loading ide-disk...
Using /lib/modules/2.4.20-boel/kernel/drivers/ide/ide-disk.o

Loading agpgart...
Assuming agpgart is compiled into the kernel, not needed, or already loaded.

Loading agpgart...
Assuming agpgart is compiled into the kernel, not needed, or already loaded.

Loading aic7xxx...
Using /lib/modules/2.4.20-boel/kernel/drivers/scsi/scsi_mod.o
Using /lib/modules/2.4.20-boel/kernel/drivers/scsi/aic7xxx/aic7xxx.o
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.8
        <Adaptec aic7899 Ultra160 SCSI adapter>
        aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs

scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.8
        <Adaptec aic7899 Ultra160 SCSI adapter>
        aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs

  Vendor: IBM-ESXS  Model: MAN3184MP     F   Rev: 5408
  Type:   Direct-Access                      ANSI SCSI revision: 03
  Vendor: IBM-ESXS  Model: MAN3367MP     F   Rev: 5408
  Type:   Direct-Access                      ANSI SCSI revision: 03
  Vendor: IBM-ESXS  Model: MAN3367MP     F   Rev: 5408
  Type:   Direct-Access                      ANSI SCSI revision: 03
  Vendor: IBM-ESXS  Model: MAN3367MP     F   Rev: 5408
  Type:   Direct-Access                      ANSI SCSI revision: 03
  Vendor: IBM-ESXS  Model: MAN3367MP     F   Rev: 5408
  Type:   Direct-Access                      ANSI SCSI revision: 03
scsi0:A:0:0: Tagged Queuing enabled.  Depth 8
scsi0:A:1:0: Tagged Queuing enabled.  Depth 8
scsi0:A:2:0: Tagged Queuing enabled.  Depth 8
scsi0:A:3:0: Tagged Queuing enabled.  Depth 8
scsi0:A:4:0: Tagged Queuing enabled.  Depth 8
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi disk sdb at scsi0, channel 0, id 1, lun 0
Attached scsi disk sdc at scsi0, channel 0, id 2, lun 0
Attached scsi disk sdd at scsi0, channel 0, id 3, lun 0
Attached scsi disk sde at scsi0, channel 0, id 4, lun 0
(scsi0:A:0): 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit)
SCSI device sda: 35548320 512-byte hdwr sectors (18201 MB)
Partition check:
 /dev/scsi/host0/bus0/target0/lun0: p1 p2 p3 p4
(scsi0:A:1): 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit)
SCSI device sdb: 71096640 512-byte hdwr sectors (36401 MB)
 /dev/scsi/host0/bus0/target1/lun0: p1
(scsi0:A:2): 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit)
SCSI device sdc: 71096640 512-byte hdwr sectors (36401 MB)
 /dev/scsi/host0/bus0/target2/lun0: p1
(scsi0:A:3): 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit)
SCSI device sdd: 71096640 512-byte hdwr sectors (36401 MB)
 /dev/scsi/host0/bus0/target3/lun0: p1
(scsi0:A:4): 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit)
SCSI device sde: 71096640 512-byte hdwr sectors (36401 MB)
 /dev/scsi/host0/bus0/target4/lun0: p1

Loading aic7xxx...
Using /lib/modules/2.4.20-boel/kernel/drivers/scsi/scsi_mod.o
Using /lib/modules/2.4.20-boel/kernel/drivers/scsi/aic7xxx/aic7xxx.o
Assuming aiusb.c: registered new driver usbdevfs
c7xxx is compileusb.c: registered new driver hub
d into the kernel, not needed, ousb-uhci.c: $Revision: 2859 $ time 22:46:07 Jul 14 2003
usb-uhci.c: High bandwidth mode enabled
r already loadedusb-uhci.c: USB UHCI at I/O 0xb000, IRQ 19
.u

Loading idesb-uhci.c: Detected 2 ports
-scsi...
Assuming ide-scsi is compiled into the kernel, not needed, or already loaded.

Loading usb-uhci...
Using /lib/modules/2.4.20-boel/kernel/drivers/usb/usbcore.o
Using /lib/modules/2.4.20-boel/kernel/drivers/usb/usb-uhci.o
usb.c: new USB bus registered, assigned bus number 1
Product: USB UHCI Root Hub
SerialNumber: b000
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver

This hosts name is: tg-v095

get_script
I will now try to get the autoinstall script:  tg-v095.sh
Excellent!  It's already here -- in the /scripts directory.

write_variables

run_autoinstall_script

I will now run the autoinstall script: /scripts/tg-v095.sh


get_arch
Partitioning /dev/sda...
Old partition table for /dev/sda:
Disk geometry for /dev/scsi/host0/bus0/target0/lun0/disc: 0.000-17357.578 megabytes
Disk label type: msdos
Minor    Start       End     Type      Filesystem  Flags
1        SCSI device sda: 35548320 512-byte hdwr sectors (18201 MB)
  0.031     15.6 /dev/scsi/host0/bus0/target0/lun0:88  primary   ex
t2        boot
2         15.688   1043.283  primary   linux-swap  
3       1043.284   3098.474  primary   reiserfs    
4       3098.474  17351.455  primary   reiserfs    
parted -s -- /dev/sda mklabel msdos || shellout
Creating partition /dev/sda1.
parted -s -- /devSCSI device sda: 35548320 512-byte hdwr sectors (18201 MB)
/sda mkpart prim /dev/scsi/host0/bus0/target0/lun0:ary ext2 0 15 || p1 shellout

parted -s -- /dev/sda set 1 boot on
SCSI device sda: 35548320 512-byte hdwr sectors (18201 MB)
 /dev/scsi/host0/bus0/target0/lun0: p1
Creating partition /dev/sda2.
parted -s -- /dev/sda mkpart primary ext2 15 1043 || shellout
SCSI device sda: 35548320 512-byte hdwr sectors (18201 MB)
 /dev/scsi/host0/bus0/target0/lun0: p1 p2
Creating partition /dev/sda3.
parted -s -- /dev/sda mkpart primary ext2 1043 3098 || shellout
SCSI device sda: 35548320 512-byte hdwr sectors (18201 MB)
 /dev/scsi/host0/bus0/target0/lun0: p1 p2 p3
Creating partition /dev/sda4.
parted -s -- /dev/sda mkpart primary ext2 3098 17357 || shellout
SCSI device sda: 35548320 512-byte hdwr sectors (18201 MB)
 /dev/scsi/host0/bus0/target0/lun0: p1 p2 p3 p4
New partition table for /dev/sda:
parted -s -- /dev/sda print
Disk geometry for /dev/scsi/host0/bus0/target0/lun0/disc: 0.000-17357.578 megabytes
Disk label type: msdos
Minor    Start       End     Type      Filesystem  Flags
1          0.031     15.688  primary   ext2        boot
2         15.688   1043.283  primary   linux-swap  
3       1043.284   3098.474  primary   reiserfs    
4       3098.474  17351.455  primary  SCSI device sdb: 71096640 512-byte hdwr sectors (36401 MB)
 reiserfs    
P /dev/scsi/host0/bus0/target1/lun0:artitioning /dev/sdb...
Old par
tition table for /dev/sdb:
Disk geometry for /dev/scsi/host0/bus0/target1/lun0/disc: 0.000-34715.156 megabytes
Disk label type: msdos
Minor    Start       End     Type      Filesystem  Flags
1          0.031  34710.754  primary               
parted -s -- /dev/sdb mklabel msdos || sSCSI device sdb: 71096640 512-byte hdwr sectors (36401 MB)
hellout
Creatin /dev/scsi/host0/bus0/target1/lun0:g partition /dev/sdb1.
parted - p1
s -- /dev/sdb mkpart primary ext2 0 34715 || shellout
New partition table for /dev/sdb:
parted -s -- /dev/sdb print
Disk geometry for /dev/scsi/host0/bus0/target1/lun0/disc: 0.000-34715.156 megabytes
Disk label type: msdos
Minor    Start       End     Type      Filesystem  Flags
1          0.031  34710.754  primary               
Partitioning /dev/sdc...
Old partition table for /dev/sdc:
Disk geometry for /dev/scsi/host0/bus0/target2/lun0/disSCSI device sdc: 71096640 512-byte hdwr sectors (36401 MB)
c: 0.000-34715.1 /dev/scsi/host0/bus0/target2/lun0:56 megabytes
Disk label type: m
sdos
Minor    Start       End     Type      Filesystem  Flags
1          0.031  34710.754  primary               
parted -s -- /dev/sdc mklabel msdos || shellout
Creating partition /dev/sdc1.
parted -s -- /dev/sdc mkpart primary ext2 0 34715 || shellout
SCSI device sdc: 71096640 512-byte hdwr sectors (36401 MB)
 /dev/scsi/host0/bus0/target2/lun0: p1
New partition table for /dev/sdc:
parted -s -- /dev/sdc print
Disk geometry for /dev/scsi/host0/bus0/target2/lun0/disc: 0.000-34715.156 megabytes
Disk label type: msdos
Minor    Start       End     Type      Filesystem  Flags
1          0.031  34710.754  primary               
Partitioning /dev/sdd...
Old partition table for /dev/sdd:
Disk geometry for /dev/scsi/host0/bus0/target3/lun0/disSCSI device sdd: 71096640 512-byte hdwr sectors (36401 MB)
c: 0.000-34715.1 /dev/scsi/host0/bus0/target3/lun0:56 megabytes
Disk label type: m
sdos
Minor    Start       End     Type      Filesystem  Flags
1          0.031  34710.754  primary               
parted -s -- /dev/sdd mklabel msdos || shellout
Creating partition /dev/sdd1.
parted -s -- /dev/sdd mkpart primary ext2 0 34715 || shellout
SCSI device sdd: 71096640 512-byte hdwr sectors (36401 MB)
 /dev/scsi/host0/bus0/target3/lun0: p1
New partition table for /dev/sdd:
parted -s -- /dev/sdd print
Disk geometry for /dev/scsi/host0/bus0/target3/lun0/disc: 0.000-34715.156 megabytes
Disk label type: msdos
Minor    Start       End     Type      Filesystem  Flags
1          0.031  34710.754  primary               
Partitioning /dev/sde...
Old partition table for /dev/sde:
Disk geometry for /dev/SCSI device sde: 71096640 512-byte hdwr sectors (36401 MB)
s csi/host0/bus0//dev/scsi/host0/bus0/target4/lun0:target4/lun0/disc: 0.000-34715.156 megabytes
Di
sk label type: msdos
Minor    Start       End     Type      Filesystem  Flags
1          0.031  34710.754  primary               
parted -s -- /dev/sde mklabel msdos || shellout
Creating partition /dev/sde1.
parted -s -- /dev/sde mkpart primary ext2 0 34715 || shelloSCSI device sde: 71096640 512-byte hdwr sectors (36401 MB)
u t
/dev/scsi/host0/bus0/target4/lun0: p1
New partition table for /dev/sde:
parted -s -- /dev/sde print
Disk geometry for /dev/scsi/host0/bus0/target4/lun0/disc: 0.000-34715.156 megabytes
Disk label type: msdos
Minor    Start     Journalled Block Device driver loaded
  End     Type      Filesystem  Flags
1          0.031  34710.754  primary               
Load additional filesystem drivers.
Using /lib/modules/2.4.20-boel/SGI XFS snapshot 2.4.20-2002-11-29_01:21_UTC with DMAPI, realtime, no debug enabled
kernel/fs/reiserfs/reiserfs.o
Using /lib/modules/2.4.20-boel/kemd: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
rnel/fs/ext2/ext2.o
Using /lib/modules/2.4.20-bmd: linear personality registered as nr 1
oel/kernel/fs/jbd/jbd.o
Using /lib/modules/2.4.20-boel/kernel/fs/ext3/ext3.o
Umd: raid0 personality registered as nr 2
sing /lib/modules/2.4.20-boel/kernel/fs/jfs/jfs.o
Using /lib/momd: raid1 personality registered as nr 3
dules/2.4.20-boel/kernel/fs/xfs/xfs.o
Ah, good.  Found an /etc/raid5: measuring checksumming speed
raidtab file.  Proceeding...
Using /lib/modules/2.4.20-boel/kernel/drivers/md/md.o
Using /lib/modules/2.4.20-boel/kernel/drivers/md/linear.o
Using /lib/modules/2.4.20-boel/kernel/drivers/md/md.o
Using /lib/modules/2.4.20-boel/kernel/dri   8regs     :  2780.400 MB/sec
vers/md/raid0.o
Using /lib/modules/2.4.20-boel/kernel/drivers/md/md.o
Using /lib/modules/2.4.20-boel/kernel/drivers/md/raid1.o
Using /lib/modules/2.4.20-boel/kernel/drivers/md/md.o
Using /lib/modules/2.4.20-boel/kernel/drivers/md/xor.o
   32regs    :  1695.200 MB/sec
   pIII_sse  :  3034.000 MB/sec
   pII_mmx   :  2797.600 MB/sec
   p5_mmx    :  2825.200 MB/sec
raid5: using function: pIII_sse (3034.000 MB/sec)
Using /lib/modulmd: raid5 personality registered as nr 4
es/2.4.20-boel/kernel/drivers/md/raid5.o
echo y | mkreiserfs /dev/sda4 || shellout

<-------------mkreiserfs, 2003------------->
reiserfsprogs 3.6.7

mkreiserfs: Guessing about desired format.. 
mkreiserfs: Kernel 2.4.20-boel is running.
Format 3.6 with standard journal
Count of blocks on the device: 3648763
Number of blocks consumed by mkreiserfs formatting process: 8323
Blocksize: 4096
Hash function used to sort names: "r5"
Journal Size 8193 blocks (first block 18)
Journal Max transaction length 1024
inode generation number: 0
UUID: d6566936-5910-40b1-ac31-888b3a4168ab
ATTENTION: YOU SHOULD REBOOT AFTER FDISK!
	ALL DATA WILL BE LOST ON '/dev/sda4'!
Continue (y/n):Initializing journal - 0%....20%....40%....60%....80%....100%
Syncing..ok

The Defense Advanced Research Projects Agency (DARPA) is the primary sponsor of
Reiser4. DARPA does not endorse this project; it merely sponsors it.

Continuing core development of version 3 is mostly paid for by Hans Reiser from
money made selling licenses in addition to the GPL to companies who don't want
it known that they use ReiserFS as a foundation for their proprietary product.
And my lawyer asked 'People pay you money for this?'.  Yup.  Hee Hee.  Life is
good.  If you buy ReiserFS, you can focus on your value add rather than
reinventing an entire FS.  You should buy some free software too....

SuSE pays for continuing work on journaling for version 3, and paid for much of
the previous version 3 work.  Reiserfs integration in their distro is
consistently solid.

MP3.com paid for initial journaling development.

Bigstorage.com contributes to our general fund every month, and has done so for
quite a long time.

Thanks to all of those sponsors, including the secret ones.  Without you, Hans
would still have that day job, and the merry band of hackers would be missing
quite a few....

Have fun.
mkdir -p /a/ || shellout
mount /dev/sda4 /a/ -t reiserfs -o defaults || shellout
reiserfs: checking transaction log (device 08:04) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
mke2fs /dev/sda1 || shellout
mke2fs 1.33 (21-Apr-2003)
Filesystem label=
OS type: Linux
Block size=1024 (log=0)
Fragment size=1024 (log=0)
4016 inodes, 16033 blocks
801 blocks (5.00%) reserved for the super user
First data block=1
2 block groups
8192 blocks per group, 8192 fragments per group
2008 inodes per group
Superblock backups stored on blocks: 
	8193

Writing inode tables: 0/21/2done                            
Writing superblocks and filesystem accounting information: done

This filesystem will be automatically checked every 20 mounts or
180 days, whichever comes first.  Use tune2fs -c or -i to override.
mkdir -p /a/boot || shellout
mount /dev/sda1 /a/boot -t ext2 -o defaults || shellout
echo y | mkreiserfs /dev/sda3 || shellout

<-------------mkreiserfs, 2003------------->
reiserfsprogs 3.6.7

mkreiserfs: Guessing about desired format.. 
mkreiserfs: Kernel 2.4.20-boel is running.
Format 3.6 with standard journal
Count of blocks on the device: 526128
Number of blocks consumed by mkreiserfs formatting process: 8228
Blocksize: 4096
Hash function used to sort names: "r5"
Journal Size 8193 blocks (first block 18)
Journal Max transaction length 1024
inode generation number: 0
UUID: 4e87275e-ce68-4ad5-8d0e-d2e6f58452db
ATTENTION: YOU SHOULD REBOOT AFTER FDISK!
	ALL DATA WILL BE LOST ON '/dev/sda3'!
Continue (y/n):Initializing journal - 0%....20%....40%....60%....80%....100%
Syncing..ok

The Defense Advanced Research Projects Agency (DARPA) is the primary sponsor of
Reiser4. DARPA does not endorse this project; it merely sponsors it.

Continuing core development of version 3 is mostly paid for by Hans Reiser from
money made selling licenses in addition to the GPL to companies who don't want
it known that they use ReiserFS as a foundation for their proprietary product.
And my lawyer asked 'People pay you money for this?'.  Yup.  Hee Hee.  Life is
goodreiserfs: checking transaction log (device 08:03) ...
.  If you buy ReiserFS, you can focus on your value add rather than
reinventing an entire FS.  You should buy some free software too....

SuSE pays for continuing work on journaling for version 3, and paid for much of
the previous version 3 work.  Reiserfs integration in their distro is
consistently solid.

MP3.com paid for initial journaling development.

Bigstorage.com contributes to our general fund every month, and has done so for
quite a long time.

Thanks to all of those sponsors, including the secret ones.  Without you, Hans
would still have that day job, and the merry band of hackers would be missing
quite a few....

Have fun.
mkdir -p /a/var || shellout
mount /dev/sda3 /a/var -t reiserfs -o defaults || shellout
Using r5 hash to sort names
ReiserFS version 3.6.25
mkswap -v1 /dev/sda2 || shellout
Setting up swapspace version 1, size = 1077506048 bytes
swapoAdding Swap: 1052248k swap-space (priority -1)
n /dev/sda2 || shellout
DESTROYING the contents of /dev/md1 in 5 seconds, Ctrl-C if unsure!
handling MD devimd: bind<scsi/host0/bus0/target1/lun0/part1,1>
ce /dev/md1
anamd: bind<scsi/host0/bus0/target2/lun0/part1,2>
lyzing super-blomd: bind<scsi/host0/bus0/target3/lun0/part1,3>
ck
disk 0: /devmd: bind<scsi/host0/bus0/target4/lun0/part1,4>
/sdb1, 35543781kmd: scsi/host0/bus0/target4/lun0/part1's event counter: 00000000
Bm, raid superblod: scsi/host0/bus0/target3/lun0/part1's event counter: 00000000
cmk at 35543680kBd: scsi/host0/bus0/target2/lun0/part1's event counter: 00000000
m
disk 1: /dev/sd: scsi/host0/bus0/target1/lun0/part1's event counter: 00000000
dc1, 35543781kB,md1: max total readahead window set to 2048k
m raid superblockd1: 4 data-disks, max readahead per data-disk: 512k
 at 35543680kB
raid0: looking at scsi/host0/bus0/target1/lun0/part1
drisk 2: /dev/sddaid0:   comparing scsi/host0/bus0/target1/lun0/part1(35543680) with scsi/host0/bus0/target1/lun0/part1(35543680)
raid0:   END
raid0:   ==> UNIQUE
r1, 35543781kB, raid0: 1 zones
raid superblock aaid0: looking at scsi/host0/bus0/target2/lun0/part1
tr 35543680kB
diaid0:   comparing scsi/host0/bus0/target2/lun0/part1(35543680) with scsi/host0/bus0/target1/lun0/part1(35543680)
raid0:   EQUAL
rsk 3: /dev/sde1,aid0: looking at scsi/host0/bus0/target3/lun0/part1
r 35543781kB, raiaid0:   comparing scsi/host0/bus0/target3/lun0/part1(35543680) with scsi/host0/bus0/target1/lun0/part1(35543680)
raid0:   EQUAL
raid0: looking at scsi/host0/bus0/target4/lun0/part1
rd superblock at aid0:   comparing scsi/host0/bus0/target4/lun0/part1(35543680) with scsi/host0/bus0/target1/lun0/part1(35543680)
raid0:   EQUAL
raid0: FINAL 1 zones
r35543680kB
aid0: zone 0
raid0: checking scsi/host0/bus0/target1/lun0/part1 ... contained as device 0
  (35543680) is smallest!.
raid0: checking scsi/host0/bus0/target2/lun0/part1 ... contained as device 1
raid0: checking scsi/host0/bus0/target3/lun0/part1 ... contained as device 2
raid0: checking scsi/host0/bus0/target4/lun0/part1 ... contained as device 3
raid0: zone->nb_dev: 4, size: 142174720
raid0: current zone offset: 35543680
raid0: done.
raid0 : md_size is 142174720 blocks.
raid0 : conf->smallest->size is 142174720 blocks.
raid0 : nb_zone is 1.
raid0 : Allocating 8 bytes for hash.
md: updating md1 RAID superblock on device
md: scsi/host0/bus0/target4/lun0/part1 [events: 00000001]<6>(write) scsi/host0/bus0/target4/lun0/part1's sb offset: 35543680
md: scsi/host0/bus0/target3/lun0/part1 [events: 00000001]<6>(write) scsi/host0/bus0/target3/lun0/part1's sb offset: 35543680
md: scsi/host0/bus0/target2/lun0/part1 [events: 00000001]<6>(write) scsi/host0/bus0/target2/lun0/part1's sb offset: 35543680
md: scsi/host0/bus0/target1/lun0/part1 [events: 00000001]<6>(write) scsi/host0/bus0/target1/lun0/part1's sb offset: 35543680
echo y | mkreiserfs /dev/md1 || shellout

<-------------mkreiserfs, 2003------------->
reiserfsprogs 3.6.7

mkreiserfs: Guessing about desired format.. 
mkreiserfs: Kernel 2.4.20-boel is running.
Format 3.6 with standard journal
Count of blocks on the device: 35543680
Number of blocks consumed by mkreiserfs formatting process: 9296
Blocksize: 4096
Hash function used to sort names: "r5"
Journal Size 8193 blocks (first block 18)
Journal Max transaction length 1024
inode generation number: 0
UUID: 12aa1aeb-f008-47a8-910c-0e2e6a48a124
ATTENTION: YOU SHOULD REBOOT AFTER FDISK!
	ALL DATA WILL BE LOST ON '/dev/md1'!
Continue (y/n):Initializing journal - 0%....20%....40%....60%....80%....100%
Syncing..ok

The Defense Advanced Research Projects Agency (DARPA) is the primary sponsor of
Reiser4. DARPA does not endorse this project; it merely sponsors it.

Continuing core development of version 3 is mostly paid for by Hans Reiser from
money made selling licenses in addition to the GPL to companies who don't want
it known that they use ReiserFS as a foundation for their proprietary product.
And my lawyer asked 'People pay you money for this?'.  Yup.  Hee Hee.  Life is
good.  If you buy ReiserFS, you can focus on your value add rather than
reinventing an entire FS.  You should buy some free software too....

SuSE pays for continuing work on journaling for version 3, and paid for much of
the previous version 3 work.  Reiserfs integration in their distro is
consistently solid.

MP3.com paid for initial journaling development.

Bigstorage.com contributes to our general fund every month, and has done so for
quite a long time.

Thanks to all of those sponsors, including the secret ones.  Without you, Hans
would still have that day job, and the merry band of hackers would be missing
quite a few....

Have fun.
mkdir -p /a/scratch/local || shellout
mount /dev/md1 /a/scratch/local -t reiserfs -o defaults,noatime || shellout
reiserfs: checking transaction log (device 09:01) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
mkdir -p /a/proc || shellout
mount proc /a/proc -t proc -o defaults || shellout
Quietly installing image...
/
flamethrower_client(ia32-compute-2003.08.22)
--------------------------------------------------------------------------------
udp-receiver --interface eth0 --portbase 9028 --nosync 2>/tmp/udp-receiver.ia32-compute-2003.08.22 | tar --overwrite -xp -C /a 2>/tmp/tar.stderr.log
.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-done!
flamethrower_client: Success!
--------------------------------------------------------------------------------
\890: Terminated
done.

flamethrower_client(override_ia32-compute-2003.08.22)
--------------------------------------------------------------------------------
udp-receiver --interface eth0 --portbase 9030 --nosync 2>/tmp/udp-receiver.override_ia32-compute-2003.08.22 | tar --overwrite -xp -C /a 2>/tmp/tar.stderr.log
...done!
flamethrower_client: Success!
--------------------------------------------------------------------------------




umount /a/var || shellout
umount /a/scratch/local || shellout
umount /a/proc || shellout
umount /a/boot || shellout
umount /a/ || shellout

Sending SIGKILL to all processes.
md: recovery thread got woken up ...
md: recovery thread finished ...
Please stand by while rebooting the system.
md: stopping all md devices.
md: marking sb clean...
md: updating md1 RAID superblock on device
md: scsi/host0/bus0/target4/lun0/part1 [events: 00000002]<6>(write) scsi/host0/bus0/target4/lun0/part1's sb offset: 35543680
md: scsi/host0/bus0/target3/lun0/part1 [events: 00000002]<6>(write) scsi/host0/bus0/target3/lun0/part1's sb offset: 35543680
md: scsi/host0/bus0/target2/lun0/part1 [events: 00000002]<6>(write) scsi/host0/bus0/target2/lun0/part1's sb offset: 35543680
md: scsi/host0/bus0/target1/lun0/part1 [events: 00000002]<6>(write) scsi/host0/bus0/target1/lun0/part1's sb offset: 35543680
md: md1 switched to read-only mode.
flushing ide devices: hdc 
Restarting system.
